Terex C5000 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 15

background image

TECH TIP 11 | RELEASED 02.28.2022 | VERSION 1.0

STEP 2: Setting the Minimum Rotation Pressure

Set the counter-balance valves, C1 and C2 or CB1 and CB2 located in the rotation slip drive

hydraulic manifold, to 800 – 1,000 PSI. This is accomplished by installing a hydraulic pressure gauge

at the inlet of the derrick control valve. Meter into rotation and monitor the hydraulic gauge pressure

required for initial boom movement in each direction. One counter-balance valve adjusts clockwise

rotation while the other adjusts counter-clockwise.

Old Style Pre 1/1/2016

PAGE 8 OF 15

«
...
6
7
8
9
10
...
»

Содержание C5000 Series
















Отзывы:

Нет отзывов

Похожие инструкции для C5000 Series

Бренд: S.D.P. Страницы: 54

Бренд: Terex Страницы: 55

Бренд: EASTMAN Страницы: 34

Бренд: SICE Страницы: 54

Бренд: Haulotte Group Страницы: 52

Бренд: Haulotte Group Страницы: 118

Бренд: Haulotte Group Страницы: 143

Бренд: Haulotte Group Страницы: 148

Бренд: Haulotte Group Страницы: 168

Бренд: Haulotte Group Страницы: 282

Бренд: CLAS Страницы: 32

Бренд: ALMAC Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды