background image

 

3-2

 
3.3  Precautions for installation 

[VKN-e/VKP-e] 

Warning

 

Before rotating the pump shaft by hand to check it, be sure to turn off the 
main power. An unexpected start of the pump may cause an accident. 

(1)  Install the product in a well-ventilated place with minimum exposure to dust and moisture. (Refer 

to the Installation location in “2.3. Standard specifications    [page 2-2]”). In particular, avoid 
installing the product in a place where the pumping liquid may be splashed on the motor section. 

Warning

 

Do not install the product in a hot or humid place. 
Otherwise, it may lead to heating, ignition or electric leak. 

(2)  Install the product so that the motor can take air in. 

(3)  Securely install the product on a flat place without 

any wobbles.   

(4)  The mounting surface must be strong enough to 

prevent the amplification of vibrations while the pump 
is running. 
(Restrict the total amplitudes in X, Y, and Z directions 
(see the right figure) to 33

μ

m at 50 Hz and to 29

μ

at 60 Hz during the operation of the pump.) 

(5)  Select a convenient place to conduct maintenance 

and inspection. Secure space for maintenance. 

(6)  The product is coated. If you need to overcoat it in a 

different color for a compelling reason, lightly 
roughen the product surface with sand paper or the 
like and then coat it, which improves the adhesion 
properties of the coating film. (Be sure to check the 
overcoatability of the paint.) 

(7)  Do not install the product in a place where a secondary hazard could occur in the event of any 

liquid leak. 

(8)  If the system could be exposed to the freezing temperature in winter, be sure to apply antifreeze 

measures such as heat insulation and heater installation to the pump, valves, piping, etc. 

(9)  Securely install the pump. 

Recommended size of pump mounting bolt:  M10 

The pump is provided with four mounting bolt-holes, but they are intended to extend the range of 

use. You can install the pump using only two diagonally-located mounting holes without any 
problems. 

Note

 

Securely fix the pump in place with the bolts. Otherwise, it may lead to 
abnormal vibration or other problems. 

(10) Do not hoist the equipment with the pump attached. Otherwise, it may damage the hoisting 

equipment/devices and the pump may fall. 

(11) When you hoist or move the pump, be sure to handle the pump carefully so that the pump section 

would not be subjected to an impact or imbalanced load. The container may greatly tilt depending 
on its center of gravity. 

Y: Measurement direction 

X: Measurement 
direction 

Z: Measurement point 

Y: Measurement 
direction

Z: Measurement 
point

X: Measurement 
direction

X, Y: Measurement point
(VKN-e/VKP-e)

Z: Measurement direction
(VKN-e/VKP-e)

VKN-e 

VKP-e 

Содержание VKN-e Series

































Отзывы: