background image

  

 

TCW122B-WD_R2            ( Firmware version 2.xx ) 

Page 3 

 

 

Link

 (green) – located on the Ethernet connector, indicates that the device is connected to 

the network; 

 

Act

 (yellow) – located on the Ethernet connector, flashes when activity is detected on the 

network. 

6.

 

Powering 

TCW122B-WD

 is designed to be supplied by adapter SYS1421-0612-W2E or similar, intended for 

use in the conditions of overvoltage category II, and priorly assessed for compliance with safety 
requirements. The power supply equipment shall be resistant to short circuit and overload in secondary 
circuit. 

When in use do not position the equipment so that it is difficult to operate the disconnecting 

device. 

 

7.

 

Environment information  

This equipment is intended for use in a Pollution Degree 2 environment, at altitudes up to 2000 

meters. 

When the controller is a part of a system, the other elements of the system shall comply with the 

EMC requirements and shall be intended for use in the same ambient conditions. 

 

8.

 

Safety 

This device must not be used for medical, life saving purposes or for any purpose where its failure 

could cause serious injury or the loss of life. 

To reduce the risk of fire, only flexible stranded wire, with cross section 0.5mm² or larger for 

wiring of digital and analog inputs and relay output of the device should be used.  

To avoid electric shock and fire hazard, do not expose this product to liquids, rain, or moisture. 

Objects filled with liquids, such as vases, should not be placed on this device. 

There is a risk of overheating (damage) of controller, if recommended free spaces to adjacent 

devices are not ensured. Joint part with external component shall have space for attachment/removal of 
the cable after installation. 

Teracom does not guarantee successful operation of the product if the product was used under 

conditions deviating from the product specifications. 

To ensure that the device works correctly follow the steps below: 

 

ensure that the device is installed correctly, refer this user manual; 

 

log in to the devices via browser program; 

 

make proper set up; 

 

set up the digital inputs to work in “dry contact” mode; 

 

short the “Din1” and “GND”; 

 

install sensor TSH1XX or TST1XX on 1-Wire bus; 

 

go to “Monitoring page” of WEB interface – proper parameters value should be displayed in 
the same time flashing “STS” led should indicate the proper operation. 

If the equipment is used in a manner not specified by the manufacturer, the protection provided 

by the equipment may be impaired. 

In no event will Teracom Ltd. be responsible or liable for indirect or consequential damages 

resulting from the use or application of this equipment. 

 
 
 
 

Содержание TCW122B-WD

















Отзывы: