background image

 

7.4

 

Network Setup page 

The Network parameters are set on this page. The following parameters can be changed: 

 

IP configuration

 – IP Address configuration can be static or dynamic (DHCP) 

 

IP  address,  Subnet  mask  ,  Default  gateway  – 

these  fields  are  active  if IP  address  is 

static

 

 

Host Name  

 

MAC – 

device MAC address

 

 

 

 

 

If multiply 

TCW110

 controllers are used on the same network, please change the IP address 

after connecting the device to the network. This will avoid devices installed on the network with 
the same factory default IP address at the same time. It may be necessary to clear the arp cache 
each time you connect new device to the network. This is done by typing 

arp -d

 in the command 

prompt of a Windows computer.

 

In order to reduce network traffic and to limit the access, the controller supports VLAN and 

MAC  address  filtering.  In  addition  to  the  MAC  address  of  the  Default  Gateway,  another  2  MAC 
addresses can be added to the filter. The filter is enabled by marking the appropriate check box 
after the MAC address.

 

 

 

 

To set up the SMTP server the following fields should be completed

 

 

Mailserver  IP  – 

IP  address  of  SMTP  mail  server,  note  that 

TCW110

  don’t  support  SMTP 

authentication 

 

E-mail – 

sender e-mail 

 
 
 

Содержание TCW110













Отзывы: