Tennant AS20035 Скачать руководство пользователя страница 1

Страница: 1 / 14

IB DM20075 (03- 2019)

INSTRUCTION BULLETIN

No. DM20075
Machine: os3
Published: 03- 2019
Rev. 05

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the

Parts List in the appropriate place in the machine manual for future

reference. Retaining the Parts List will make it easier to reorder

individual parts and will save the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for

kit numbers AS20035, AS20036 (connection kits), AS20047, AS20048,

AS20049, AS20050 (tank kits)

SYNOPSIS:

This kit contains the parts needed to install the os3 satellite dispenser system and transport

containers.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: Ambient temperature must be between 50- 110

(10- 43

C) in area where os3 is installed.

(Estimated time to complete: 1.25 hours)

Refer to schematic on the last page of this document (Fig. 54) for system level plumbing reference.

PROTECT THE ENVIRONMENT

Please dispose of packaging materials, used machine components

such as batteries and fluids in an environmentally safe way according

to local waste disposal regulations.
Always remember to recycle.

North America:

Account number for labor

charges related to installing the os3:

63012.

Authorizing Name:

Orbio

Europe (CE) Installs:

Account number for labor

charges related to installing the os3 Cleaning

Solution Generator:

609040.

Authorizing Name:

Orbio

PREPARATION:

1. Consult the Site Survey (Evaluation)

document to determine the location for os3

satellite station and any other site specific

installation requirements.

NOTE: If volume dispensed for 1 minute at 35 psi

is less than 2.5 gallons (9.5 liters), replace the

yellow eductor in port 1 with the provided brown

eductor. Refer to Site Survey (Evaluation)

document for water pressure information.

2. Use stud finder to locate studs behind the

wall. Mark stud locations on the wall. (Fig. 1)

FIG. 1

Содержание AS20035















Результаты поиска

Содержание AS20035

Отзывы:

Похожие инструкции для AS20035

Бренды по названию

Популярные бренды

Tennant AS20035, Инструкционный бюллетень

Результаты поиска

Содержание AS20035

Отзывы:

Похожие инструкции для AS20035

Бренды по названию

Популярные бренды