Tennant 355E Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 72

Tennant 355E Скачать руководство пользователя страница 31

OPERATION

29

355E MM306 (6–93)

SWEEPING AND BRUSH INFORMATION

Pick up oversized debris before sweeping. Flatten
or remove bulky cartons from aisles before
sweeping. Pick up pieces of wire, twine, string,
etc., which could become entangled in brush or
brush plugs.

Plan the sweeping in advance. Try to arrange long
runs with minimum stopping and starting. Sweep
debris from very narrow aisles into main aisles
ahead of time. Do an entire floor or section at one
time. Sweep as straight a path as possible. Avoid
bumping into posts or scraping the sides of the
sweeper. Overlap the brush paths.

Avoid turning the steering wheel too sharply when
the machine is in motion. The machine is very
responsive to the movement of the steering
wheel. Avoid sudden turns, except in
emergencies.

Check the brush daily for wear or damage.
Remove any string or wire tangled on the main
brush, main brush drive hub, or main brush idler
hub.

Check the main brush pattern daily. The pattern
should be 50 to 75 mm (2.0 to 3.0 in) wide with
the main brush in the Down position. Adjust the
main brush pattern by turning the main brush
pressure knob located next to the brush position
lever.

For best results, use the correct brush type for
your sweeping application. The following are
recommendations for main and side brush
applications.

Nylon 8-double Row Main Brush –
Recommended for general sweeping and has
good hopper loading. Nylon has the longest life
then any bristle types, use this brush for sweeping
rough or irregular surfaces.

Polypropylene and Wire 8-double Row Main
Brush – The wire bristles loosen slightly packed
soilage and heavier debris. The polypropylene
bristles sweep up the debris with excellent hopper
loading.

07817

08002

«
...
29
30
31
32
33
...
»

Содержание 355E









































































Отзывы:

Нет отзывов