manualshive.com logo in svg

Ten-Tec AT588K, Инструкция по эксплуатации

Поделиться
Скачать
Ten-Tec AT588K Скачать руководство пользователя страница 1

INSTRUCTION MANUAL – MODEL AT588K

Model AT588K is a user-installable kit to add the internal automatic antenna tuner to an
existing model 588 Omni-VII transceiver.  Instructions, complete with color photos of
relevant detail, are included in this manual.

Model AT588K is a “no-solder” kit.  You will need the following tools:

#10 Torx wrench (provided with the kit, Ten-Tec part #38313).
Small pair of needle nose pliers.
2 Philips screwdrivers, one small, one large.

We recommend you read this manual in its entirety before beginning installation of the
tuner kit.  

Should you have difficulty installing the tuner or need advice, our service department is
available to provide technical support from 8 a.m. to 5 p.m. USA Eastern time by calling
(865) 428-0364.

Ten-Tec, Inc., 1185 Dolly Parton Parkway, Sevierville, TN 37862 USA
Sales:  (800) 833-7373.  General Info and Office:  (865) 453-7172.
Service:  (865) 428-0364.   Visit us on the web at 

www.tentec.com

Ten-Tec part #74431
Version 1 – February 2009

Содержание AT588K

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды