Quick Guide
TempSen
®
Tempod
®
SP Temperature Data Logger
1> Overview
2> Operation Instructions
©2015. All rights reserved, TempSen Electronics Company
4> Battery
5> Important Information
Battery Expiry Date (EXP Date) is printed on the rear side of
each logger, Tempod SP logger may stop recording if it's
used later than EXP Date, so please check EXP Date every
time starting a Tempod SP to avoid recording failure.
QG_TEMPODSP_150327_EN_CN REV. A
Start Recording
Configuration
Press
START/STOP
button and hold for 5 seconds to start. LEDs
flash in turn for 3 times means data logger successfully starts
recording
.
Tempod SP data logger should be configured before starting
recording, please connect Tempod SP to PC and configure
logger with TempCentre software.
Press
START/STOP
button and hold for 5 seconds to stop
recording. LEDs flash for 3 times indicating recording stopped.
Logger also would stop recording after running out preset
logging cycle.
Plug Tempod SP into USB port of PC, then copy PDF report
from removable storage device "
TempSenDisk"
to your
computer.
You could also download Tempod SP using TempCentre
software. Please download TempCentre from
www.tempsen.com.
Download Data
Stop Recording
TempSen warrants this TempSen-branded hardware product against
defects in materials and workmanship under normal use for a period
of ONE (1) YEAR from the date of retail purchase by the original end-
user purchaser (“Warranty Period”). If a hardware defect arises and
a valid claim within the Warranty Period, as its option and to the
extent permitted by law, TempSen will either (1) repair the hardware
defect at no charge, using new parts or parts equivalent to new in
performance and reliability, (2) exchange the new product with a
product is new or equivalent to new in performance and reliability
and is at least functionally equivalent to the original product, or (3)
refund the purchase price of this product. TempSen may request that
you replace defective parts with new or refurbished user-installable
parts that TempSen provides in fulfillment of its warranty obligation. A
replacement product or parts, including a user-installable part that has
been installed in accordance with instructions provided by TempSen,
assumes the remaining warranty of the original product or ninety (90)
days from the date of replacement or repair, whichever provides
longer coverage for you. When a product or part is exchanged, any
replacement item becomes your property and the replaced item
becomes TempSen’s property. Parts provided by TempSen in fulfillment
it’s warranty obligation must be used in products for which warranty
service is claimed. When a refund is given, the product for which
the refund is provided must be returned to TempSen and becomes
TempSen’s property.
EXCLUSIONS AND LIMITATIONS
This Limited Warranty applies only to the hardware product
manufactured by or for TempSen that can be identified by the
“TempSen” trademark, trade name, or logo affixed to it. The Limited
Warranty does not apply to any non-TempSen hardware product or
any software, even if packaged or sold with the TempSen hardware.
Manufacturers, suppliers, publishers, other than TempSen, may provide
their own warranties to the end user purchaser, but TempSen, in so
far as permitted by law, provides their products “as is”. Software
distributed by TempSen with or without the TempSen brand name
(including, but not limited to system software) is not covered under this
Limited Warranty. Refer to the licensing agreement accompanying the
software for details of your rights with respect to its use.
TempSen does not warrant that the operation of product will be
uninterrupted or error-free. TempSen is not responsible for the damage
arising from failure to follow instructions relating to the product’s use.
This warranty does not apply: (a) to consumable parts, such as
batteries, unless damage has occurred due to a defect in materials
or workmanship; (b) to cosmetic damage, including but not limited to
scratches, dents, and broken plastic on ports; (c) to damage caused
with non-TempSen products; (d) to damage caused by accident,
abuse, misuse, flood, fire, earthquake, or other external causes; (e)
to damage caused by operating the product outside the permitted
or intended uses described by TempSen; (f) to damage caused by
service (including upgrades and expansions) performed by anyone
who is not a representative of TempSen or TempSen Authorized Service
Provider; (g) to a product or part that has been modified to alter
functionality or capability without the written permission of TempSen; or
(h) if any TempSen serial number has been removed or defaced.
IMPORTANT: DO NOT OPEN THE HARDWARE PRODUCT. OPENING THE
HARDWARE PRODUCT MAY CAUSE DAMAGE THAT IS NOT COVERED BY
THIS WARRANTY. ONLY TEMPSEN OR AN AUTHORIZED SERVICE PROVIDER
SHOULD PERFORM SERVICE ON THIS HARDWARE PRODUCT.
6> Warranty
Please call us at +86 21 6768 5210 or send email to
[email protected] for technical assistance.
USB Plug
Start/Stop Button
LED Indicators
Actions
LED Sequences
Start Recording
&
flash in turn for 3 times
During Recording
-No Alarm-
flashes every 10 seconds
During Recording
-Alarmed-
flashes every 10 seconds
Stop Recording
&
flash for 3 times
After Stopped
-No Alarm-
flashes 2 times every 2 seconds
After Stopped
-Alarmed-
flashes 2 times every 2 seconds
Connecting to PC
&
become solid
lights off 1 second after
connected indicating logger starts to
generate PDF report.
3> LED Indication
a) To avoid damaging your Tempod SP data logger, please
do not disconnect it from USB port while it is communicating
with the computer.
b) Data stored in Tempod SP data logger is retrievable even
battery runs out.
c) Tempod SP data logger uses CR2032 lithium battery, please
do not heat, microwave or recharge it.
d) Please follow local regulations when recycling or disposing
of Tempod SP data loggers.
Please do not configure a Tempod SP if you don't
intend to use it immediately, Tempod SP after
connected to computer would start to consume
power and shorten rated shelf life.
