manualshive.com logo in svg

Teltronics SEB NET-PATH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Teltronics SEB NET-PATH Скачать руководство пользователя страница 37

NET-PATH Installation and Operation Guide

Page 2-13

Temperature 
Sensor

The NET-PATH provides one internal temperature sensor and a connector for an 
optional external temperature sensor. The temperature range for both are from -10° to 
190° F, with an accuracy and resolution of +/- 1° F. User-specified temperature deltas 
determine when change in temperature events are generated. The NET-PATH can be 
programmed to detect specific temperature values to determine reportable 
temperature events. Temperatures can be reported in Fahrenheit, Celsius, and Kelvin.

Internal Temperature Sensor

The internal temperature sensor is positioned near the UPS battery charging circuit 
and is used to detect excessive charging temperatures that may occur during abnormal 
charging conditions. The battery charger is turned off until the internal temperature 
returns to an acceptable level. You can program your NET-PATH to report specific 
internal temperature events based on database parameters, or generate an event when 
the battery charger turns off or on.

External Temperature Sensor 

The optional external temperature sensor is available to monitor the temperature 
within the facility where the NET-PATH is installed. The database can be 
programmed to look for specific temperature values and take action, such as report 
events to the maintenance center or to activate a fan via a power control device. 

The external temperature sensor, shown below, connects to the NET-PATH using a 
cable terminated with RJ45 male connectors at both ends. The sensor has two input 
jacks, either of which can be used. 

Figure 2-17  NET-PATH External Temperature Sensor

Note 

The DC Voltage Sensor input wiring table is 

provided above, but connection to this connector should 
only be made using the optional DC Voltage sensor 
cable. Consult the factory for details. 

Содержание SEB NET-PATH



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды