manualshive.com logo in svg

Teltronics SEB NET-PATH, Инструкция по установке и эксплуатации

Поделиться
Скачать
Teltronics SEB NET-PATH Скачать руководство пользователя страница 22

Description and Specifications

Page 1-4

Hardware 
Specifications

Modem

•

56K internal modem

•

V.42 MNP (2-4) error correction

•

V.42 BIS MNP5 data compression

•

Group 3 Fax

Microprocessor

•

Motorola 860T

•

32 MB FLASH Memory

•

128  MB  S  DRAM

Dimensions

•

Height 1.75 inches

•

Width 17 inches (fits 19” rack)

•

Depth10.5 inches

Weight

•

Approximately 12 lb.

Environmental Requirements

•

50

°

 to 110

°

 F operating temperature (10

°

 to 43

°

 C)

•

20

°

 

to 140

°

 F non-operating temperature (-29

°

 to 60

°

 C)

•

20% to 80% relative humidity, nonconducting

Power Requirements

*The DC input range is -36 V to -72 V; -48 VDC nominal.

Host System Interface

Depending on the options you choose, the NET-PATH can have four to eight EIA RS-
232-C serial ports. Connectors for the NET-PATH (labeled Host 1 through Host n) are 
configured as Data Terminal Equipment (DTE), using RJ45 male connectors. 
Transmission rates can vary from 110 BPS to up to 115 KBPS.

Telephone Line Interface

The telephone connection is a modular RJ11C interface. Pulse dialing or tone 
signaling (DTMF) is a software option.

Input power

Voltage

Current

Watts

BTU/hr

AC

110 volts

180 mA

19.80

67.56

DC*

48 volts

250 mA

12.00

40.95

Содержание SEB NET-PATH



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды