Telit Wireless Solutions ME310G1-W1 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 96

background image

ME310G1 Hardware Design Guide

1VV0301588 Rev. 12

Page 91 of 96

2021-06-14

Safety Recommendations

Make sure the use of this product is allowed in your country and in the environment
required. The use of this product may be dangerous and has to be avoided in areas where:

•

it can interfere with other electronic devices, particularly in environments such as
hospitals, airports, aircrafts, etc.

•

there is a risk of explosion such as gasoline stations, oil refineries, etc. It is the
responsibility of the user to enforce the country regulation and the specific
environment regulation.

Do not disassemble the product; any mark of tampering will compromise the warranty
validity. We recommend following the instructions of the hardware user guides for
correct wiring of the product. The product has to be supplied with a stabilized voltage
source and the wiring has to be conformed to the security and fire prevention regulations.
The product has to be handled with care, avoiding any contact with the pins because
electrostatic discharges may damage the product itself. Same cautions have to be taken
for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM
when the product is in power saving mode.

The system integrator is responsible for the functioning of the final product. Therefore,
the external components of the module, as well as any project or installation issue, have
to be handled with care. Any interference may cause the risk of disturbing the GSM
network or external devices or having an impact on the security system. Should there be
any doubt, please refer to the technical documentation and the regulations in force. Every
module has to be equipped with a proper antenna with specific characteristics. The
antenna has to be installed carefully in order to avoid any interference with other
electronic devices and has to guarantee a minimum distance from the body (20 cm). In
case this requirement cannot be satisfied, the system integrator has to assess the final
product against the SAR regulation.

The equipment is intended to be installed in a restricted area location.

The equipment must be supplied by an external specific limited power source in
compliance with the standard EN 62368-1:2014.

The European Community provides some Directives for the electronic equipment
introduced on the market. All of the relevant information is available on the European
Community website:

https://ec.europa.eu/growth/sectors/electrical-engineering_en

«
...
89
90
91
92
93
...
»

Содержание ME310G1-W1

































































































Отзывы:

Нет отзывов

Похожие инструкции для ME310G1-W1

Бренд: Hawking Страницы: 2

Бренд: Ubiquiti Страницы: 16

Бренд: Atlantis Land Страницы: 2

Бренд: Gogen Страницы: 22

Бренд: Linksys Страницы: 44

Бренд: Loopcomm Страницы: 66

Бренд: Loopcomm Страницы: 83

Бренд: Aztech Страницы: 20

Бренд: BandLuxe Страницы: 80

Бренд: Colubris Networks Страницы: 3

Бренд: Sony Страницы: 3

Бренд: AmbiCom Страницы: 40

Бренд: AmbiCom Страницы: 27

Бренд: HPE Страницы: 4

Бренд: HPE Страницы: 4

Бренд: Cambium Networks Страницы: 24

Бренд: Cambium Networks Страницы: 56

Бренд: Cambium Networks Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды