Telit Wireless Solutions BLUEMOD+S42/AI/ADC/LUA Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 85

Telit Wireless Solutions BLUEMOD+S42/AI/ADC/LUA Скачать руководство пользователя страница 60

S42

Hardware User Guide

1VV0301303 Rev. 11

Page 60 of 85

2021-05-06

Not Subject to NDA

8.2.2.

FCC Statement

This device complies with 47 CFR Part 2 and Part 15 of the FCC Rules and with.

Operation is subject to the following two conditions:

1.

this device my not cause harmful interference, and

2.

this device must accept any interference received, including interference that may
cause undesired operation.

8.2.3.

FCC Caution

Warning: Changes or modifications made to this equipment not
expressly approved by Telit may void the FCC authorization to operate
this equipment.

8.2.4.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital
device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide
reasonable  protection  against  harmful  interference  in  a  residential  installation.  This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.  However,  there  is  no guarantee  that interference  will  not  occur  in  a
particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or
television reception, which can be determined by turning the equipment off and on, the
user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following
measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

8.2.5.

FCC RF-exposure Statement

The S42/AI complies with the FCC/IC RF radiation exposure limits set forth for
an uncontrolled environment.

«
...
58
59
60
61
62
...
»

Содержание BLUEMOD+S42/AI/ADC/LUA






















































































Отзывы:

Нет отзывов