Televes H30 CRYSTAL Скачать руководство пользователя страница 17

Страница: 17 / 40

7. Satellite Test

This function checks that the input signal

corresponds to the selected satellite, and at the

same time checks the proper reception of the

selected transponders (from 1 to 4 transponders).

To do that, the meter performs all the

measurements on those transponders.
First of all the user must select the channel plan of

the satellite towards which the antenna is oriented.
Then the user must select the transponders on

which you want to carry out the measurements

(see Setup section of this function).
The information necessary to verify the satellite

is extracted from these channels, and the

measurements of the selected transponders are

displayed.

7.1. Main window

Below is a capture of a Satellite Test window with a

brief explanation of its features:

List of measurements

with pass/fail indicators

Press OK to see all the

measurements

Bar graph representing

the selected channels

Color according to

checkmarks

Selected channel

Change using

7.2. Setup

Press

to change the Satellite Test options.

- Powering:

Select the powering of the LNB if

needed.

- DiSEqC:

Select the SAT of the DiSEqC

command.

SCR (only satellite band)

: Selects the SCR

parameters (multiswitch, standard and slots)

When a slot is enabled (for example slot 3,

freq. 1210MHz), the meter will tune into the

slot frequency (1210MHz) and will set the slot

with the meter parameters: frequency, band

(powering), and DiSEqC. In addition, a SCR

icon will be shown in the bar at the top (SCR3)

to indicate that the slot is enabled.

While the slot is enabled, all the setting

changes of the meter, will be applied to the

currently slot (SCR3).

- Ref. Level:

Select the reference level of the

bar graph.

- Channels:

Select the number of channels as

well as the channels from the channel plan.

8. Learning plan

Analyzes the input signal to the meter and

automatically detects all channels.
This feature automatically identifies the channels

as either analog or digital and performs

measurements on each.
A bar graph is displayed with the height

representing the power for digital channels and the

level of the video carrier for the analog channels.

Satellite checked

Содержание H30 CRYSTAL









































Результаты поиска

Содержание H30 CRYSTAL

Отзывы:

Бренды по названию

Популярные бренды

Televes H30 CRYSTAL, Инструкция по эксплуатации

Результаты поиска

Содержание H30 CRYSTAL

Отзывы:

Бренды по названию

Популярные бренды