Teledyne WORKHORSE Скачать руководство пользователя страница 103

Страница: 103 / 258

WorkHorse H-ADCP Operation Manual

May

2015

EAR-Controlled Technology Subject to Restrictions Contained on the Cover Page.

Page 91

System Overview

This section presents a functional description of H-ADCP operation using block diagrams.

Operating Modes

The H-ADCP has two modes of operation: command mode, and ping mode (also referred to as “Deploy-

ment Saver” Mode). Depending on what mode the H-ADCP is in; it will go either to sleep, or to resume

pinging.

Command Mode

Whenever you wake up your H-ADCP, power dissipation increases from less than 1 mW to around 2.2 W.

If you leave the H-ADCP in command mode without sending a command for more than 5 minutes, the H-

ADCP automatically goes to sleep. This protects you from inadvertently depleting batteries.

•

If the H-ADCP receives a BREAK, it will go to the command prompt and wait for a command.

The H-ADCP will wait at the command prompt for five minutes. If no commands have been

sent, it will go to sleep (also called “Battery Saver” mode).

•

If you press the reset switch (located on the CPU board), the H-ADCP will go to sleep.

•

If the H-ADCP receives a CS-command, it will go into the ping mode and begin pinging. If a

TF-command (Time of First Ping) was sent prior to the CS-command, then the H-ADCP will

go to sleep until the TF time occurs.

•

If the H-ADCP does a COLD wakeup (i.e. an unknown state), it will go to the command

prompt.

•

If the H-ADCP is asleep for approximately nine hours, it wakes up to charge the capacitor

used to maintain RAM. Once the capacitor is charged (this only takes a few seconds), the H-

ADCP goes back to sleep.

Ping Mode

After you send commands to the H-ADCP that tells it to start collecting data, the H-ADCP goes into de-

ployment saver mode. If power is somehow removed and later restored, the H-ADCP simply picks up

where it left off and continues to collect data using the same set up.

•

If the H-ADCP receives a BREAK, it will go to the command prompt, but stays in the ping

mode. If a valid command is received, the H-ADCP will switch to the command mode. If no

valid command is received, a warning will be displayed after four minutes, indicating that the

system will self-deploy. After a total of five minutes with no input, the H-ADCP will resume

pinging.

•

If you press the reset switch, and an alarm is currently set for the next ping, the H-ADCP will

go to sleep. If no alarm is set, the system will start a new deployment and starts pinging im-

mediately unless a TF-command had been set after the last BREAK. In this case, the H-ADCP

will go to sleep until the TF time occurs.

•

If the H-ADCP does a COLD wakeup, the system will start a new deployment and starts ping-

ing immediately unless a TF-command had been set after the last BREAK. In this case, the H-

ADCP will go to sleep until the TF time occurs if the TF time is valid (i.e., not in the past).

•

If the H-ADCP is asleep for approximately nine hours, it wakes up to charge the capacitor

used to maintain RAM. Once the capacitor is charged, if a valid alarm is set for the next ping

time, the H-ADCP goes back to sleep and waits for the alarm. If no alarm is set, the H-ADCP

will resume pinging immediately, or wait for the TF time (if valid), and then start pinging.

Содержание WORKHORSE



































































































































































































































































Результаты поиска

Содержание WORKHORSE

Отзывы:

Teledyne WORKHORSE, Руководство по эксплуатации, Страница: 103 / 258

Результаты поиска

Содержание WORKHORSE

Отзывы: