manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 69 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 69

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

65 

NOTE 

If the analyzer beeps when you press the EXIT  button, it means that you’ve made a 

change/entered a new value for a parameter but have not caused it to be accepted by 

pressing ENTR first. 

4.4.1.

 

SETUP – CFG: VIEWING THE ANALYZER’S 

CONFIGURATION INFORMATION 

Pressing the CFG button  displays the instrument configuration information. This display 
lists the analyzer model, serial number, firmware revision, software library revision, CPU 
type and other information. Use this information to identify the software and hardware 
when contacting Technical Support. Special  instrument or software features or installed 
options  may also be listed here.  

 

 

SAMPLE*           RANGE = 500.0 PPB        H2S =X.XXX  
 

 

< TST  TST >  CAL  

 

 

             

SETUP

 

SAMPLE          

ENTER SETUP PASS : 818

 

 

        

 8        1        8 

 

                          

ENTR

   

EXIT

 

 SAMPLE 

         

PRIMARY SETUP MENU

  

 

 

CFG

  DAS  RNGE  PASS  CLK  MORE                  EXIT 

 SAMPLE 

       

T101 SO2-H2S ANALYZER

       

 

 

NEXT

   

 PREV

                                                          EXIT 

Press EXIT at 

any time to 

return to 

SETUP menu 

Press EXIT at 

any time to 

return to the 

SAMPLE display 

 Press NEXT of PREV to move back 

and forth through the following list 

of Configuration information: 

•

 

MODEL NAME 

•

 

SERIAL NUMBER  

•

 

SOFTWARE REVISION 

•

 

LIBRARY REVISION 

•

 

iCHIP SOFTWARE REVISION

1 

•

 

HESSEN PROTOCOL REVISION

1 

•

 

ACTIVE SPECIAL SOFTWARE 

OPTIONS

1 

•

 

CPU TYPE 

•

 

DATE FACTORY CONFIGURATION 

SAVED 

1

Only appears if relevant option of Feature is active. 

 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов