manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 61 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 61

 

 

57 

4.

 

OPERATING INSTRUCTIONS 

The  T101  is a micro-computer-controlled  analyzer  with a dynamic menu interface for 
easy and yet powerful and flexible operation.  All major operations are controlled from 
the front panel touch screen control.  

To assist in navigating the system’s software, a series of menu trees can be found in 
Appendix  A of this manual. 

 

NOTE   

The ENTR  button  may disappear if you select a setting that is invalid or out of the allowable range for that 

parameter, such as trying to set the 24-hour  clock to 25:00:00.   Once you adjust the setting to an 

allowable value, the ENTR button will reappear. 

4.1.

 

OVERVIEW  OF OPERATING  MODES 

The T101 software has a variety of operating modes.  Most commonly, the analyzer will 
be operating in 

SAMPLE

  mode.  In this mode, a continuous read-out of the H

2

S 

concentration is displayed on the front panel and output as an analog voltage from rear 
panel terminals, calibrations can be performed, and 

TEST

  functions and 

WARNING

 

messages can be examined. 

The second most important operating mode is 

SETUP

  mode.  This mode is used for 

performing certain configuration operations, such as for the DAS  system, the reporting 
ranges, or the serial (RS-232/RS-485/Ethernet) communication channels.  The

 SET UP

 

mode is also used for performing various diagnostic  tests during troubleshooting. 

The Mode field of the front panel display indicates to the user which operating mode the 
unit is currently running. 

In addition  to 

SAMPLE 

and 

SETUP

, other modes the analyzer can be operated in are: 

Table 4-1. Analyzer Operating Modes 

MODE 

DESCRIPTION 

DIAG 

One of the analyzer’s diagnostic modes is active (Section 4.6).  

M-P CAL 

This is the basic calibration mode of the instrument and is activated by pressing 

the CAL button. 

SAMPLE 

Sampling normally,  flashing text indicates adaptive filter is on. 

SAMPLE A 

Indicates that unit is in SAMPLE mode and AUTOCAL feature is activated. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов