Teledyne T101 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 375

Teledyne T101 Скачать руководство пользователя страница 41

Teledyne ML – T101 Operation Manual

Getting Started

37

Table 3-5. Status Output Signals

REAR PANEL

LABEL

STATUS

DEFINITION

CONDITION

1

SYSTEM OK

ON if no faults are present.

2

CONC VALID

OFF any time the HOLD OFF feature is active, such as during calibration

or when other faults exist possibly invalidating the current concentration

measurement (example: sample flow rate is outside of acceptable limits).
ON if concentration measurement is valid.

3

HIGH RANGE ON if unit is in high range of the AUTO Range Mode

4

ZERO CAL

ON whenever the instrument’s ZERO point is being calibrated.

5

SPAN CAL

ON whenever the instrument’s SPAN point is being calibrated.

6

DIAG MODE

ON whenever the instrument is in DIAGNOSTIC mode

7 - 8

SPARE

D

EMITTER BUS The emitters of the transistors on pins 1-8 are bussed together.

SPARE

+

DC POWER

+ 5 VDC, 300 mA source (combined rating with Control Output, if used).

Digital

Ground

The ground level from the analyzer’s internal DC power supplies

3.3.4.

CONNECTING THE CONTROL INPUTS

If you wish to use the analyzer to remotely activate the zero and span calibration modes,
several digital control inputs are provided through a 10-pin connector labeled CONTROL
IN on the analyzer’s rear panel.

There are two methods for energizing the control inputs. The in5V available from
the pin labeled “+” is the most convenient method. However, if full isolation is required,
an external 5 VDC power supply should be used.

«
...
39
40
41
42
43
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов