manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 315 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 315

Teledyne API T/E-Series Models 101, 102, and 108 Software Documentation (PN05492D DCN6485)

 

A-21 

APPENDIX A-3: Warnings and Test Measurements, S/W Version C.7 (E-Series), 1.0.5 

(T-Series) 
 

Table A-2:     Warning Messages 

Name

 1

 

Message Text 

Description 

Warnings 

WSYSRES 

SYSTEM RESET 

Instrument was power-cycled or the 

CPU was reset. 

WDATAINIT DATA 

INITIALIZED  Data storage was erased. 

WCONFIGINIT 

CONFIG INITIALIZED 

Configuration storage was reset to 

factory configuration or erased. 

WSO2ALARM1 

7

 

SO2 ALARM 1 WARN 

SO

2

 concentration alarm limit #1 

exceeded 

WSO2ALARM2 

7

 

SO2 ALARM 2 WARN 

SO

2

 concentration alarm limit #2 

exceeded 

WH2SALARM1 

7

 

H2S ALARM 1 WARN 

H

2

S/TRS concentration alarm limit 

#1 exceeded 

WH2SALARM2 

7

 

H2S ALARM 2 WARN 

H

2

S/TRS concentration alarm limit 

#2 exceeded 

WTRSALARM1 

7+5

 

TRS ALARM 1 WARN 

TRS concentration alarm limit #1 

exceeded 

WTRSALARM2 

7+5

 

TRS ALARM 2 WARN 

TRS concentration alarm limit #2 

exceeded 

WPMT 

PMT DET WARNING 

PMT detector outside of warning 

limits specified by DETECTOR_LIMIT 

variable. 

WUVLAMP 

UV LAMP WARNING 

UV lamp reading outside of warning 

limits specified by DETECTOR_LIMIT 

variable. 

WOXYFLOW 

6

 

OXY FLOW WARNING 

Oxygenator flow outside of warning 

limits specified by OXY_FLOW_SET 

variable. 

WSAMPFLOW 

SAMPLE FLOW WARN 

Sample flow outside of warning 

limits specified by SAMP_FLOW_SET 

variable. 

WSAMPPRESS 

SAMPLE PRESS WARN 

Sample pressure outside of warning 

limits specified by SAMP_PRESS_SET 

variable. 

WCONVTEMP 

4

 

CONV TEMP WARNING 

Converter temperature outside of 

warning limits specified by 

CONV_SET

 variable. 

WBOXTEMP 

BOX TEMP WARNING 

Chassis temperature outside of 

warning limits specified by BOX_SET 

variable. 

WRCELLTEMP 

RCELL TEMP WARNING 

Reaction cell temperature outside of 

warning limits specified by 

RCELL_SET

 variable. 

WIZSTEMP 

IZS TEMP WARNING 

IZS temperature outside of warning 

limits specified by IZS_SET variable. 

07266B DCN6485

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов