Teledyne T101 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 375

Teledyne T101 Скачать руководство пользователя страница 28

Specifications and Approvals

Teledyne ML – T101 Operation Manual

24

PARAMETER

DESCRIPTION

Standard I/O

1 Ethernet: 10/100Base-T

2 RS-232 (300 – 115,200 baud)

2 USB device ports

8 opto-isolated digital status outputs

6 opto-isolated digital control inputs

4 analog outputs

Optional I/O

1 USB com port

1 RS485

8 analog inputs (0-10V, 12-bit)

4 digital alarm outputs

Multidrop RS232

3 4-20mA current outputs

For indoor use at altitudes ≤ 2000m only

2.2.

APPROVALS AND CERTIFICATIONS

The Teledyne ML Model T101 analyzer was tested and certified for Safety and
Electromagnetic Compatibility (EMC). This section presents the compliance statements
for those requirements and directives.

2.2.1.

SAFETY

IEC 61010-1:2001, Safety requirements for electrical equipment for

measurement, control, and laboratory use.

CE: 2006/95/EC, Low-Voltage Directive

North American:

cNEMKO (Canada): CAN/CSA-C22.2 No. 61010-1-04

NEMKO-CCL (US): UL No. 61010-1 (2nd Edition)

2.2.2.

EMC

EN 61326-1 (IEC 61326-1), Class A Emissions/Industrial  Immunity
EN 55011 (CISPR 11), Group 1, Class A Emissions
FCC 47 CFR Part 15B, Class A Emissions
CE:  2004/108/EC, Electromagnetic Compatibility Directive

2.2.3.

OTHER TYPE CERTIFICATIONS

For additional certifications, please contact Technical Support:

Toll-free Phone: 800-846-6062

Phone: 303-792-3300

Fax: 303-799-4853

Email: [email protected]

«
...
26
27
28
29
30
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов