manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 264 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 264

Principles Of Operation 

Teledyne ML - T101 Operation Manual

 

260

 

10.3.7.

 

PNEUMATIC SENSORS 

The T101 uses two pneumatic sensors to verify gas streams. These sensors are located 
on a printed circuit assembly, called the pneumatic pressure/flow sensor board. 

10.3.7.1.

 

Sample  Pressure Sensor 

An absolute pressure transducer plumbed to the input of the analyzer’s sample chamber 
is used to measure the pressure of the sample gas before it enters the chamber. This 
upstream used to validate the critical flow condition (2:1 pressure ratio) through the 
instrument’s critical flow orifice (Section 10.3.3.1). Also, if the temperature/pressure 
compensation (TPC) feature is turned on (Section 10.7.3), the output of this sensor is 
also used to supply  pressure data for that calculation. 

The actual pressure measurement is viewable through the analyzer’s front panel display 
as the test function

 PRESS

. 

10.3.7.2.

 

Sample Flow Sensor 

A thermal-mass flow sensor is used to measure the sample flow through the analyzer. 
This sensor is also mounted on the pneumatic pressure/flow sensor board upstream of 
the sample chamber. The flow rate is monitored by the CRT which issues a warning 
message (

SAMP FLOW WARN

) if the flow rate is too high or too low. 

The  flow  rate  of  the  sample  gas is viewable via the front panel as the 

SAMP FL

 test 

function. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов