manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 242 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 242

Troubleshooting & Service 

Teledyne ML - T101 Operation Manual

 

238

 

Table 9-9. Example of UV Lamp Power Supply Outputs 

UVLAMP_SIGNAL 

ACTION  TO BE TAKEN 

3500mV±200mV. 

No  Action Required 

> 4900mV  at any time. 

Adjust the UV reference  detector potentiometer  (refer to Figure 9-6) 

until UVLAMP_SIGNAL  reads approximately  3600mV  before 

continuing  to adjust  the lamp  position. 

>3700mV   or < 3300mV  Adjust the UV reference  detector potentiometer  (refer to Figure 9-6) 

until UVLAMP_SIGNAL  reads as  close to 3500mV  as possible.    

.< 600mV 

Replace the lamp. 

 

 

Figure 9-5. Location of UV Reference Detector Potentiometer 

5.

 

Finger-tighten  the thumbscrew.   

NOTE 

DO NOT over-tighten the thumbscrew.

 

 

9.6.3.

 

REPLACING THE UV LAMP 

1.

 

Turn off the analyzer. 

27.

 

Disconnect the UV lamp from its power supply.  

•

 

You can find the power supply  connector by following  the two, white 

UV Lamp power supply wires from the lamp  to the power supply. 

28.

 

Loosen, but do not remove  the two UV lamp  bracket screws and  the 

large brass thumbscrew located on the shutter housing (refer to Figure 

9-4) so that the lamp  can be moved.   

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов