manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 239 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 239

Teledyne ML - T101 Operation Manual 

Troubleshooting  & Service

 

 

235 

The IZS option is heated with a proportional heater circuit and the temperature is 
maintained at 50° C ±1°. Check the 

IZS TEMP

 function via front panel display (Section 

4.2.1) and the 

IZS_TEMP

  signal voltage using the 

SIGNAL I/O

  function under the 

DIAG

  Menu (Section  4.6.1). At 50°

 

C, the temperature signal from the IZS thermistor 

should  be around 2500 mV. 

9.5.18.

 

BOX TEMPERATURE  

The box temperature sensor (thermistor) is mounted on the motherboard at the bottom, 
right corner of the CPU board when looking at it from the front. It cannot be 
disconnected to check its resistance. Box temperature will vary with, but will always 
read about 5° C higher than, ambient (room) temperature because of the internal heating 
zones from the H

2

S converter, sample chamber and other devices. To check the box 

temperature functionality, we recommend checking  the 

BOX_TEMP

  signal voltage 

using the 

SIGNAL I/O

 function under the 

DIAG

 Menu (Section 4.6.1). At about 30°

 

C 

(5

°

  above typical room temperature), the signal should be around 1500 mV. We 

recommend using a certified or calibrated external thermometer / temperature sensor to 
verify the accuracy of the box temperature. 

9.5.19.

 

PMT TEMPERATURE 

PMT temperature should be low and constant. It is more important that this temperature 
is maintained constant than it is to maintain it low. The PMT cooler uses a Peltier, 
thermo-electric element powered by 12 VDC from the switching power supply PS2. The 
temperature is controlled by a proportional temperature controller located on the 
preamplifier board. Voltages applied to the cooler element vary from +/- 0.1 to +/- 12 
VDC. The temperature set point (hard-wired into the preamplifier board) will vary by 
about ±1

°

 C due to component tolerances. The actual temperature will be maintained to 

within 0.1

°

 C around that set point. On power-up of the analyzer, the front panel enables 

the user to watch that temperature drop from about ambient temperature down to its set 
point of 6-8° C. If the temperature fails to drop after 20 minutes, there is a problem in 
the cooler circuit. If the control circuit on the preamplifier board is faulty, a temperature 
of -1

°

 C is reported. 

9.6.

 

REPAIR PROCEDURES 

This section contains some procedures that may need to be performed when a major 
component of the analyzer requires repair or replacement. Note that replacement 
procedures that are discussed in detail in Section  8  (Maintenance) are not listed here.  
Servicing of circuit components requires electrostatic discharge protection, i.e. ESD 
grounding straps, mats and containers.  Failure to use ESD protection when working 
with electronic assemblies will void  the instrument warranty. 

9.6.1.

 

DISK-ON-MODULE REPLACEMENT 

Replacing the Disk-on-Module (DOM) will cause loss of all DAS data; it also may 
cause loss of some instrument configuration parameters unless the replacement DOM 
carries the exact same firmware version.  Whenever changing the version of installed 
software, the memory  must be reset. Failure to ensure that memory is  reset can cause the 
analyzer to malfunction, and invalidate measurements. After the memory is reset, the 
A/D converter must be re-calibrated, and all information collected in Step 1 below must 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов