manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 236 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 236

Troubleshooting & Service 

Teledyne ML - T101 Operation Manual

 

232

 

•

 

Make sure that the communications  software is functioning properly. 

Further help with serial communications is available in a separate manual “RS-232 
Manual”, Teledyne ML 

part number 013500000, available online at 

http://www.Teledyne-ml.com/manuals/. 

9.5.12.

 

PMT SENSOR 

The photo multiplier tube detects the light emitted by the UV excited fluorescence of 
H

2

S. It has a gain of about 500000 to 1000000. It is not possible to test the detector 

outside of the instrument in the field. The best way to determine if the PMT is working 
properly is by using the optical test (

OTEST

), which is described in Section 4.6.4. The 

basic method to diagnose a PMT fault is to eliminate the other components using 

ETEST

, 

OTEST

 and specific tests for other sub-assemblies. 

9.5.13.

 

PMT PREAMPLIFIER BOARD 

To check the correct operation of the preamplifier board, we suggest the technician carry 
out  the  electrical  and optical tests described in Sections 4.6.4 and 4.6.5. If the 

ETEST

 

fails,  the preamplifier board may be faulty. 

9.5.14.

 

PMT TEMPERATURE CONTROL PCA 

The TEC control printed circuit assembly is located on the sensor housing assembly, 
under the slanted shroud, next to the cooling  fins and directly above the cooling  fan. 

If the red LED located on the top edge of this assembly is not glowing the control circuit 
is not receiving power. Check the analyzers power supply, the Relay board’s  power 
distribution circuitry and the wiring connecting them to the PMT temperature control 
PCA. 

TEC Control  Test Points 

Four test points are also located at the top of this assembly they are numbered left to 
right start with the T1 point immediately to the right of the power status LED.  These 
test points provide information  regarding the functioning  of the control circuit. 

•

 

To determine  the current running  through  the control circuit, measure 

the voltage between T1 and  T2.  Multiply  that voltage by 10. 

•

 

To determine  the drive  voltage being  supplied  by the control circuit to 

the TEC, measure  the voltage between T2 and T3. 

•

 

If this voltage is zero, the TEC circuitry is most likely open. 

Or, 

•

 

If the voltage between T2 and T3 =  0 VDC and the voltage measured 

between T1 and T2 = 0 VDC there is most likely  an open circuit or 

failed op amp on control PCA itself 

•

 

If the voltage between T2 and T3 =  0 VDC and the voltage measured 

between T1 to T2 is some voltage other than 0 VDC,  the TEC is most 

likely shorted 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов