Teledyne T101 Скачать руководство пользователя страница 234

Страница: 234 / 375

Troubleshooting & Service

Teledyne ML - T101 Operation Manual

230

40 mV

0.4

60 mV

0.6

80 mV

0.8

100

100 mV

1.0

9.5.9.3.

Status Outputs

The procedure below can be used to test the Status outputs.

Connect a cable jumper between the “-“ pin and the “



” pin on the status

output connector.

21.

Connect a 1000 Ω resistor between the +5 V and the pin for the status

output that is being tested.

Table 9-8. Status Outputs Check Pin Out

PIN

(left to right)

STATUS

System Ok

Conc Valid

High Range

Zero Cal

Span Cal

Diag Mode

Spare

22.

Connect a voltmeter between the “-“ pin and the pin of the output being

tested (Table 11-8).

23.

Under the DIAG > SIGNAL I/O menu (Section 4.6.1), scroll through

the inputs and outputs until you get to the output in question. Alternately

turn on and off the output noting the voltage on the voltmeter, it should

vary between 0 volts for ON and 5 volts for OFF.

9.5.9.4.

Control Inputs

The control input bits can be tested by the following procedure:

Connect a jumper from the +5 V pin on the STATUS connector to the +5 V

on the CONTROL IN connector.

24.

Connect a second jumper from the ‘-‘ pin on the STATUS connector to

the A pin on the CONTROL IN connector. The instrument should switch

from SAMPLE mode to ZERO CAL R mode.

25.

Connect a second jumper from the ‘-‘ pin on the STATUS connector to

the B pin on the CONTROL IN connector. The instrument should switch

from SAMPLE mode to SPAN CAL R mode.

In each case, the T101 should return to SAMPLE mode when the jumper is removed.

9.5.10.

CPU

There are two major types of CPU board failures, a complete failure and a failure
associated with the Disk-On-Module (DOM). If either of these failures occur, contact
the factory.

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 234 / 375

Результаты поиска

Содержание T101

Отзывы: