Teledyne T101 Скачать руководство пользователя страница 231 | Manualshive

Страница: 231 / 375

Teledyne T101 Скачать руководство пользователя страница 231

Teledyne ML - T101 Operation Manual

Troubleshooting & Service

227

several LEDs should turn on as soon as the power is supplied. If an incorrect power
configuration is suspected, check for the correct voltage and frequency at the line input
on the rear panel.

If the unit is set for 220-240 V and is plugged into 100-120 V, the analyzer will not start.

If the unit is set for 100-120 V and is plugged into 220-240 V, the circuit breaker built
into the ON/OFF Switch on the front panel will trip to the OFF position immediately
after power is switched on. Note that the analyzer will be severely damaged if 220-240
V is supplied to it when configured for 100-120 V. Never bypass the power switch or
circuit breaker.

9.5.4.

DC POWER SUPPLY

If you have determined that the analyzer’s AC main power is working, but the unit is
still not operating properly, there may be a problem with one of the instrument’s
switching power supplies, which convert AC power to 5 and ±15 V (PS1) as well as +12
V DC power (PS2). The supplies can either have DC output at all or a noisy output
(fluctuating).

To assist tracing DC Power Supply problems, the wiring used to connect the various
printed circuit assemblies and DC powered components and the associated test points on
the relay board follow a standard color-coding scheme as defined in Table 11-4.

Table 9-4. DC Power Test Point and Wiring Color Code

NAME

TEST POINT#

COLOR

DEFINITION

DGND

1

Black

Digital ground

+5V

2

Red

AGND

3

Green

Analog ground

+15V

4

Blue

-15V

5

Yellow

+12V

6

Purple

+12R

7

Orange

12 V return (ground) line

A voltmeter should be used to verify that the DC voltages are correct as listed in Table
11-5. An oscilloscope, in AC mode and with band limiting turned on, can be used to
evaluate if the supplies are excessively noisy (>100 mV peak-to-peak).

Table 9-5. DC Power Supply Acceptable Levels

POWER

SUPPLY VOLTAGE

CHECK RELAY BOARD TEST POINTS

MIN V

MAX V

From Test Point

To Test Point

Name

#

Name

#

PS1

+5

DGND

1

+5

2

+4.80

+5.25

PS1

+15

AGND

3

+15

4

+13.5

+16.0

PS1

-15

AGND

3

-15V

5

-14.0

-16.0

PS1

AGND

AGND

3

DGND

1

-0.05

+0.05

«
...
229
230
231
232
233
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов