manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 228 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 228

Troubleshooting & Service 

Teledyne ML - T101 Operation Manual

 

224

 

•

 

The sample  delivery  system may  be contaminated. Check for dirt in the 

sample lines or sample chamber. 

•

 

Calibration  gas source may be contaminated. 

•

 

Dilution  air contains sample or span gas. 

•

 

Sample  inlet may be contaminated with H

2

S exhaust from  this or other 

analyzers. Verify proper  venting of the pump  exhaust. 

•

 

Span gas overflow is not properly  vented and creates a back-pressure on 

the sample  inlet port. Also, if the span gas is not vented at all and does 

not supply  enough  sample  gas, the analyzer  may  be evacuating the 

sample  line.  Make  sure to create and properly  vent excess span  gas. 

•

 

If the instrument  is equipped  with an intern  IZS valve option and the H

2

S 

span value is continuously trending  downward, the IZS permeation  tube 

may require replacement 

9.3.7.

 

DISCREPANCY BETWEEN ANALOG OUTPUT AND DISPLAY 

If the concentration reported through the analog outputs does not agree with the value 
reported on the front panel, you may need to re-calibrate the analog outputs. This 
becomes more likely when using a low concentration or low analog output range. 
Analog outputs running at 0.1 V full scale should always be calibrated manually. See 
Section 4.6.3.3 for a detailed description  of this procedure. 

9.4.

 

OTHER PERFORMANCE PROBLEMS 

Dynamic problems (i.e. problems which only manifest themselves when the analyzer is 
monitoring sample gas) can be the most difficult and time consuming to isolate and 
resolve. The following section provides an itemized list of the most common dynamic 
problems with recommended troubleshooting  checks and corrective actions. 

9.4.1.

 

EXCESSIVE NOISE 

Excessive noise levels under normal operation usually indicate leaks in the sample 
supply or the analyzer itself. Make sure that the sample or span gas supply is leak-free 
and carry out a detailed leak check as described earlier in this chapter. 

Another possibility of excessive signal noise may be the preamplifier board, the high 
voltage power supply and/or the PMT detector itself. Contact the factory on trouble-
shooting  these components. 

9.4.2.

 

SLOW RESPONSE 

If the analyzer starts responding too slowly to any changes in sample, zero or span gas, 
check for the following: 

•

 

Dirty or plugged sample filter or sample lines. 

•

 

Sample  inlet line is too long. 

•

 

Dirty or plugged critical flow orifices. Check flows (Section 9.5.2), 

pressures (Section 9.5.1), and if necessary, change the critical flow 

orifice (Section 8.3.7). 

•

 

Wrong materials in contact with sample - use Teflon materials only. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов