manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 211 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 211

Teledyne ML – T101 Operation Manual 

Instrument Maintenance

 

 

207 

Converter Efficiency  =   490.3 ÷ 499.1 
Converter Efficiency  =   0.982 (98.2%) 

10.

 

It is recommended  that the H

2

S 

 SO

2

 converter  catalyst material  be 

replaced  if the converter efficiency falls below 96%  or whatever efficiency 

rating is specified by local regulatory requirements. 

8.3.5.3.

 

Changing the H

2

S 

 SO

2

 Converter Catalyst Material   

The H

2

S 

 SO

2

 converter is located in the center of the instrument, see Figure 3-5 for 

location, and Figure 8-3 for the assembly. The converter is designed for replacement of 
the cartridge only; the heater with built-in  thermocouple can be reused. 

•

 

Turn off the analyzer power, remove  the cover and allow  the converter to 

cool. 

•

 

Remove  the top lid  of the converter as well  as the top layers  of the 

insulation  until  the converter cartridge  can be seen. 

 

CAUTION 

The converter operates at 315º C. Severe burns can result if the 

assembly is not allowed  to cool. Do not handle the assembly until  it is at 

room temperature. This may take several hours. 

 

•

 

Remove  the tube fittings from  the converter. 

•

 

Disconnect the power  and the thermocouple  of the converter. Unscrew 

the grounding  clamp of the power leads with a Phillips-head  screw driver. 

•

 

Remove  the converter assembly  (cartridge and band heater) from  the 

can. Make  a note of the orientation  of the tubes relative  to the heater 

cartridge. 

•

 

Unscrew the band heater and loosen it, take out the old converter 

cartridge. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов