manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 209 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 209

Teledyne ML – T101 Operation Manual 

Instrument Maintenance

 

 

205 

8.3.4.

 

CHANGING THE EXTERNAL ZERO AIR SCRUBBER 

The chemicals in the external scrubber need to be replaced periodically according to 
Table 9-1 or as needed. This procedure can be carried out while the instrument is 
running.  Make sure that the analyzer is not in ZERO calibration mode. 

1.

 

Locate the scrubber on the outside rear panel. Figure 9-2 shows an 

exploded  view of the scrubber assembly. 

 

Figure 8-2. Charcoal Canister Assembly 

2.

 

Remove  the old scrubber by disconnecting the 1/4” plastic tubing from 

the particle filter using  9/16” and 1/2"  wrenches. 

3.

 

Remove  the particle filter from the cartridge using 9/16” wrenches. 

4.

 

Unscrew the top of the scrubber  canister and  properly disposition  the 

charcoal contents in  accordance with local laws about discarding  these 

chemicals. The rebuild  kit (listed in Appendix  B) comes with a Material 

and Safety Data Sheet, which contains more  information  on these 

chemicals. 

5.

 

Refill  the scrubber canister with charcoal. 

6.

 

Place a retainer  pad  over the charcoal, and then close the cartridge with 

the screw-top cap. 

7.

 

Tighten the cap on the scrubber - hand-tight only. 

8.

 

Replace the DFU filter with a new unit and discard the old. 

9.

 

Replace the scrubber assembly  into its clips on the rear panel. 

10.

 

Reconnect the plastic  tubing  to the fitting  of  the particle  filter. 

11.

 

Adjust the scrubber cartridge such that it does not protrude  above or 

below the analyzer in case the instrument  is mounted in a rack. If 

necessary, squeeze the clips for a tighter grip  on the cartridge. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов