manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 184 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 184

Calibration Procedures  

Teledyne  ML  – T101 Operation Manual 

180 

  

Table 6-3. AutoCal Attribute Setup Parameters 

Attribute Name 

ACTION 

Timer Enabled 

Turns on the Sequence timer 

Starting Date 

Sequence will operate on Starting Date 

Starting Time 

Sequence will operate at Starting Time 

Delta Days 

Number of days to skip between each sequence 

Delta Time 

Incremental delay on each Delta Day that the sequence starts. 

Duration 

Duration of the sequence in minutes 

Calibrate 

Enable to do dynamic zero/span calibration, disable to do a cal check only. 

This must be set to OFF for units used in US EPA applications and with IZS 

option installed. 

 

NOTE 

The programmed  STARTING_TIME  must be a minimum of 5 minutes later than the real 

time clock (See Section 4.4.6 for setting real time clock). 

 

NOTE 

Avoid setting two or more sequences at the same time of the day. Any new sequence 

which is initiated whether from a timer, the COM ports, or the contact closure inputs  will 

override any sequence which is in progress. 

 

NOTE 

If at any time an illegal entry is selected (Example: Delta Days > 367) the ENTR  button 

will disappear from the display. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов