Teledyne T101 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 375

Teledyne T101 Скачать руководство пользователя страница 164

Remote Operation

Teledyne ML – T101 Operation Manual

160

5.1.4.7.

Setting Hessen Protocol Status Flags

Teledyne  ML’s  implementation of Hessen protocols includes a set of status bits that the
instrument includes in responses to inform the host computer of  its condition. Each bit
can be assigned to one operational and warning message flag.  The default settings for
these bit/flags are:

Table 5-8. Default Hessen Status Bit Assignments

NOTES

It is possible to assign more than one flag to the same Hessen status bit. This allows the

grouping of similar flags, such as all temperature warnings, under the same status bit.

Be careful not to assign conflicting flags to the same bit as each status bit will be

triggered if any of the assigned flags is active.

STATUS FLAG NAME

DEFAULT BIT

ASSIGNMENT

WARNING FLAGS
SAMPLE FLOW WARNING

0001

PMT DET WARNING

0002

UV LAMP WARNING

0002

HVPS WARNING

0004

DARK CAL WARNING

0008

RCELL TEMP WARNING

0010

IZS TEMP WARNING

0020

PMT TEMP WARNING

0040

CONV TEMP WARNING

1000

OPERATIONAL FLAGS
Instrument Off

0100

In Manual Calibration Mode

0200

In Zero Calibration Mode

0400

In Span Calibration Mode

0800

UNITS OF MEASURE FLAGS
UGM

0000

MGM

2000

PPB

4000

PPM

6000

SPARE/UNUSED BITS

0080, 8000

UNASSIGNED FLAGS
Box Temp Warning

Analog Cal Warning

Sample Press Warning

Cannot Dyn Zero

System Reset

Cannot Dyn Span

Rear Board Not Detected

Invalid Conc

Relay Board Warning

«
...
162
163
164
165
166
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов