manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 159 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 159

Teledyne ML – T101 Operation Manual 

Remote Operation 

 

155 

5.1.4.

 

USING THE T101 WITH A HESSEN PROTOCOL NETWORK 

5.1.4.1.

 

General Overview of Hessen Protocol 

The Hessen protocol is a Multidrop  protocol, in which several remote instruments are 
connected via a common communications channel to a host computer.  The remote 
instruments are regarded as slaves of the host computer.  The remote instruments are 
unaware that they are connected to a Multidrop  bus and never initiate Hessen protocol 
messages.  They only respond to commands from the host computer and only when they 
receive a command containing their own unique ID number. 

The Hessen protocol is designed to accomplish two things: to obtain the status of remote 
instruments, including the concentrations of all the gases measured; and to place remote 
instruments into zero or span calibration or measure mode. TML’s implementation 
supports both of these principal  features.  

The Hessen protocol is not well defined; therefore while TML’s application is completely 
compatible with the protocol itself, it may be different from implementations by other 
companies. 

The following subsections describe the basics for setting up your instrument to operate 
over a Hessen Protocol network. For more detailed information as well as a list of host 
computer commands and examples of command and response message syntax, download 
the  Manual Addendum for Hessen Protocol  from the Teledyne ML  web site: 
http://www.teledyne-ml.com/manuals/index.asp  . 

5.1.4.2.

 

Hessen COMM Port Configuration 

Hessen protocol requires the communication  parameters of the T101’s COMM ports to be 
set differently than the standard configuration as shown in the table below. 

Table 5-6. Hessen RS-232 Communication Parameters 

Parameter 

Standard 

Hessen 

Data Bits 

8 

7 

Stop Bits 

1 

2 

Parity 

None 

Even 

Duplex 

Full 

Half 

To change the rest of the COMM port parameters and modes, see Section 4.10.8. 

To change the baud rate of the T101’s COMM ports, see Section 4.10.9. 

NOTE 

Make sure that the communication  parameters of the host computer are also properly 

set. 

Also, the instrument  software has 200 ms latency before it responds to commands 

issued by the host computer. This latency should present no problems, but you should be 

aware of it and not issue commands to the instrument  too frequently. 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов