Teledyne T101 Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 375

Teledyne T101 Скачать руководство пользователя страница 141

Teledyne ML – T101 Operation Manual

Operating Instructions

137

To define the

REPORT PERIOD

, follow the instruction shown in Section 4.11.2.2 then

press:

Edit Data Channel Menu

SETUP X.X

0)

CONC: ATIMER, 2, 4032, R

PREV NEXT INS DEL

EDIT

PRNT

EXIT

Exits to the main

Data Acquisition

menu.

SETUP X.X

NAME:CONC

<SET

SET>

EDIT

PRINT

EXIT

Press

SET>

until you reach

REPORT PERIOD

…

SETUP X.X

REPORT PERIODD:DAYS:0

0 0 0

ENTR EXIT

ENTR

accepts the new string and

returns to the previous menu.

EXIT

ignores the new string and

returns to the previous menu.

Press to set length of time

between reports in the format :

HH:MM (max: 23:59).

Set the number of days

between reports (0-366).

If at any time an illegal entry is selected (e.g., days > 366) the

ENTR button will disappear from the display.

SETUP X.X

REPORT PERIODD:TIME:01:01

0 0 0 5

ENTR EXIT

SETUP X.X

REPORT PERIOD:000:00:05

<SET SET>

EDIT

PRINT

EXIT

Use PREV and NEXT to

scroll to the data channel

to be edited.

From the

DATA ACQUISITION

menu

4.8.2.6.

Number of Records

The number of data records in the DAS is cumulative across all channels and parameters,
filling about one megabyte of space on the disk-on-module; this means that  the  actual
number of records is  limited by the total number of parameters and channels and other
settings in the DAS  configuration. Every additional data channel (up to 20), parameter (up
to 50 per channel), number of samples setting etc. will govern the maximum amount of
data points.

The  DAS  will check the amount of available data space and prevent the user from
specifying too many records at any given point. If, for example, the DAS  memory space
can accommodate 375 more data records, the ENTR button will disappear when trying to
specify more than that number of records. This check for memory space may also make
an upload of a DAS  configuration with APICOM or a Terminal program fail, if the

«
...
139
140
141
142
143
...
»

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов