manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 135 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 135

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

131 

4.8.2.2.

 

Editing DAS Data Channels 

DAS  configuration is most conveniently done through the APICOM remote control 
program. The following  list  of key strokes shows how to edit using the front panel. 

 

 

 

 
 

Main Data Acquisition Menu 

Edit Data Channel Menu 

 SAMPLE           RANGE = 500.0 PPB           

H2S 

=XXX.X     

 
 < TST  TST >  CAL  

 

 

SETUP

 

 

 

 

SETUP X.X     

  

0)

 

CONC:     ATIMER,     2,         4032, R

 

 
 

PREV  NEXT

    

        INS    DEL   EDIT     PRNT    EXIT

 

SETUP X.X 

 

     

 

PRIMARY SETUP MENU

 

  

 
 CFG   

DAS

  

RNGE

  

PASS  CLK  MORE 

EXIT

 

SAMPLE          

ENTER SETUP PASS : 818

 

 
        

 8        1        8 

 

                      

ENTR

  

 EXIT

 

 

EXIT

 will return to  the 

previous 

SAMPLE

 

display. 

SETUP X.X       

     

DATA ACQUISITION

 

 

 

 

 VIEW

 

 

 

 

 

 

EDIT

 

 

 

 

 

EXIT

 

Moves the 

display up & 

down the list of 
Data Channels

 

Inserts a new Data 

Channel into the list 

BEFORE the Channel 

currently being displayed 

 

Deletes The Data 
Channel currently 

being displayed 

 

Exports the 

configuration of all 

data channels to 

RS-232 interface. 

Exits to the Main 

Data Acquisition 

Menu 

 

 

 

SETUP X.X      

NAME:CONC

 

 

<SET SET>

 

 EDIT  PRNT       

 

EXIT

 

Moves the display 

between the 

properties for this data 

channel.

 

Reports the configuration of current 

data channels to the RS-232 ports. 

EXIT returns to the 

previous Menu 

To edit the channel name, see next sequence. 

 

When editing the data channels, the top line of the display indicates some of the 
configuration  parameters. For example, the display line: 

0) CONC: ATIMER,  4, 800 

translates to the following  configuration:

 

Channel No.: 0 
NAME: CONC 
TRIGGER EVENT: ATIMER 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов