manualshive.com logo in svg

Teledyne T101, Руководство по эксплуатации, Страница: 109 / 375

Поделиться
Скачать
Teledyne T101 Скачать руководство пользователя страница 109

Teledyne ML – T101 Operation Manual 

Operating Instructions 

 

105 

4.7.2.

 

COM PORT DEFAULT SETTINGS 

As received from the factory, the analyzer is set up to emulate a DCE or modem, with pin 
3 of the DB-9 connector designated for receiving data and pin 2 designated for sending 
data. 

•

 

RS232: RS-232 (fixed) DB-9 male connector. 

o

 

Baud rate: 115200  bits per  second (baud). 

o

 

Data Bits: 8 data bits with 1 stop bit. 

o

 

Parity: None. 

•

 

COM2: RS-232 (configurable), DB-9 female connector. 

o

 

Baud rate: 19200  bits per second (baud). 

o

 

Data Bits: 8 data bits with 1 stop bit. 

o

 

Parity: None. 

CAUTION 

Cables that appear to be compatible because of matching connectors  may incorporate internal wiring that 

make the link inoperable. Check cables acquired from sources other than Teledyne ML for pin 

assignments before using. 

4.7.3.

 

RS-232 COM PORT CABLE CONNECTIONS 

In its default configuration, the T101  analyzer has two available RS-232 Com ports 
accessible via 2  DB-9 connectors on the back panel of the instrument.  The COM1 
connector is a male DB-9 connector and the COM2 is a female DB9 connector. 

 

Figure 4-7. Rear Panel Connector Pin-Outs  for RS-232 Mode 

Содержание T101
























































































































































































































































































































































































Отзывы:

Нет отзывов