Teledyne T101 Скачать руководство пользователя страница 100

Страница: 100 / 375

Operating Instructions

Teledyne ML – T101 Operation Manual

4.6.3.7.

Analog Inputs (XIN1…XIN8) Option Configuration

To configure the analyzer’s

optional analog inputs

define for each channel

•

gain (number of units represented by 1 volt)

•

offset (volts)

•

engineering units to be represented in volts (each press of the touchscreen button

scrolls the list of alphanumeric characters from A-Z and 0-9)

•

whether to display the channel in the Test functions

To adjust settings for the Analog Inputs option parameters press:

DIAG AIO

XIN1 GAIN:1.00V/V

SET> EDIT

EXIT

DIAG

ANALOG I / O CONFIGURATION

PREV

NEXT

ENTR

EXIT

DIAG AIO

AOUTS CALIBRATED: NO

< SET SET> CAL

EXIT

DIAG AIO

XIN1 GAIN:1.00V/V

+ 0 0 1 .0 0

ENTR

EXIT

Press to change

Gain value

DIAG AIO

XIN1:1.00,0.00,V,OFF

< SET SET> EDIT

EXIT

Press

SET>

to scroll to the first

channel. Continue pressing

SET>

to view each of 8 channels.

Pressing

ENTR

records the new setting

and returns to the previous menu.

Pressing

EXIT

ignores the new setting and

returns to the previous menu.

Press

EDIT

at any channel

to to change Gain, Offset,
Units and whether to display
the channel in the Test
functions (OFF/ON).

DIAG AIO

XIN1 OFFSET:0.00V

< SET

SET> EDIT

EXIT

DIAG AIO

XIN1 UNITS:V

< SET SET> EDIT

EXIT

DIAG AIO

XIN1 DISPLAY:OFF

< SET EDIT

EXIT

Figure 4-6. DIAG – Analog Inputs (Option) Configuration Menu

Содержание T101
























































































































































































































































































































































































Результаты поиска

Содержание T101

Отзывы:

Teledyne T101, Руководство по эксплуатации, Страница: 100 / 375

Результаты поиска

Содержание T101

Отзывы: