Teledyne PS200 Series Скачать руководство пользователя страница 48

Страница: 48 / 58

PS200

PORTABLE GAS MONITOR

OPERATOR MAINTENANCE

64171, Rev. 11/December 2019

8-2

• Place the filter cover over the filter recess and slide it towards the display until the locating lugs

engage in the locating slots.

• Using a No.1 Pozidrive

screwdriver, tighten the captive screw.

.2. SAMPLE INLET (DUST) FILTER REPLACEMENT

Figure 8-2: Sample Inlet (Dust) Filter Replacement

• Using a No.1 Pozidrive

screwdriver, remove the 2 Pozi Pan screws.

• Remove the inlet nozzle. The sample inlet filter is located at the rear of the inlet nozzle.
• Push a matchstick, or similar, into the front of the inlet nozzle and remove the sample inlet filter

from the rear of the inlet nozzle.

• Insert a new sample inlet filter into the rear of the inlet nozzle. Ensure the ‘rough’ surface faces

the inlet filter (sample side).

• Replace the inlet nozzle. The inlet nozzle will only fit in one direction.
• Using a No.1 Pozidrive

screwdriver, insert the 2 Pozi Pan screws.

NOTE: Ensure that the locating pegs in the monitor filter recess align with the mating

pin-holes in the hydrophobic filter.

NOTE: Do not overtighten the captive screw.

NOTE: Do not overtighten the screws.

Содержание PS200 Series



























































Результаты поиска

Содержание PS200 Series

Отзывы:

Teledyne PS200 Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 48 / 58

Результаты поиска

Содержание PS200 Series

Отзывы: