manualshive.com logo in svg

Teledyne Princeton Instruments IsoPlane 81, Руководство пользователя

Поделиться
Скачать
Teledyne Princeton Instruments IsoPlane 81 Скачать руководство пользователя страница 11

11

Chapter 2:

IsoPlane 81 System

This chapter provides an introduction to, and overview information about, Teledyne 
Princeton Instruments’ IsoPlane 81 Imaging Spectrometer System.

The IsoPlane 81 is an integrated 80.8 mm focal length imaging spectrometer with a 
built-in 256 x 1024 (row x column) TEC-cooled back-illuminated CCD detector and a 
motorized single-turret grating drive. Its proprietary optical design produces 
diffraction-limited imaging with zero coma or astigmatism at any wavelength across 
the entire focal plane of the sensor.

Figure 2-1 shows the items typically included as part of a standard IsoPlane 81 Imaging 
Spectrometer System.

Figure 2-1:

Typical IsoPlane 81 System Components

The following items are included as standard equipment with every IsoPlane 81 system:

•

IsoPlane 81 Software: Powered by LightField;

Each IsoPlane 81 ships with fully featured software powered by Teledyne 
Princeton Instruments' 64-bit LightField software. For users requiring a full 
license to run other TPI hardware, please contact your local sales associate.

•

Laser-Cut Entrance Slit;

A precision laser-cut slit is shipped with each unit. Each slit is laser engraved 
with its width on the handled end of the slit carrier.

NOTE:

Additional slits are sold separately.

Содержание Princeton Instruments IsoPlane 81































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды