Teledyne PowerMAX Скачать руководство пользователя

Страница: 54 / 62

215861 REV C

Installation, Outdoor HPO PowerMAX System

3.1.13.8 System Link Cable (L213828-4)

The System Link Cable, part number L213828-4, connects the 16-way system’s Out-

door SSPA Controllers and the RF Detector module housed within the system RF Dis-

tribution Box. This cable is used to pass online/standby status information between the

amplifiers.

A label is affixed near each cable connector that describes the port to which it should

be attached. Plug the connectors into the appropriate ports (Port J8 of each Controller

and Port J8 of the 16-way system RF Distribution Box). See

Figure 3-22

3.1.13.9 Optional Ethernet Cables

Connect each Outdoor SSPA Controller to the optional Ethernet Switch using the pro-

vided Ethernet cables, part number L213824-X. See

Figure 3-23

Figure 3-22: System Link Cable, L213828-4

Figure 3-23: Ethernet Cables, L213824-X

Содержание PowerMAX































































Результаты поиска

Содержание PowerMAX

Отзывы:

Похожие инструкции для PowerMAX

Бренды по названию

Популярные бренды

Teledyne PowerMAX, Руководство по установке

Результаты поиска

Содержание PowerMAX

Отзывы:

Похожие инструкции для PowerMAX

Бренды по названию

Популярные бренды