Teledyne Optima Скачать руководство пользователя страница 45

Страница: 45 / 112

Section 2 Installation

2-27

2.11.3 Sample Interval

SMPL. Interval

: Press F3 to select the

AMPLING

NTERVAL

setting. Use the up and

down arrows to scroll through the options and
select F3 to accept. Generally, the sampling
interval is a set time, in between samples.

2.11.4 Time Option

Use the up or down arrow keys to scroll to the
desired option (e.g. Time Fixed). Press F3 to
accept.

SMPL Min

: Use the keypad to enter the

desired S

AMPLING

IME

NTERVAL

or leave as is,

then press F3 to accept.

2.11.5 Bottle Options

Sample Type

: Use arrows to scroll and press

F3 to select C

OMPOSITE

ISCRETE

EQUENTIAL

AMPLING

type.

• If D

ISCRETE

AMPLE

YPE

was selected,

the next menu is B

OTTLE

ONFIG

. Use

the arrows to scroll to the desired bottle
configuration that is installed in the
sampler, then press F3 to select.

Num. Bottles

: Enter the number of bottles

that you want to use, otherwise press F3 to
accept the default setting to use all the bottles.

SAMPLS/Bottle

: Enter the number of samples

that you want to collect in every bottle. Then
press F3 to accept this setting. Be sure to not
overfill the sample bottles.

Содержание Optima

















































































































Результаты поиска

Содержание Optima

Отзывы:

Teledyne Optima, Карманный справочник, Страница: 45 / 112

Результаты поиска

Содержание Optima

Отзывы: