Teledyne Optima Скачать руководство пользователя страница 27

Страница: 27 / 112

Section 2 Installation

2-9

2.4.1 24-1 Liter

The 24 bottle configurations use a rack to hold

and align the containers. To install the bottles
in the refrigerator using the rack:

1. Place the uncapped bottles into the rack.

Install bottle retaining ring and fasten with
the 3 bungee cords.

2. Pull the sequential table forward. (Platinum

only).

3. Locate the arrow in center of the rack and

align it with the center block located on the
turn table.

4. Roll the sequential table back into the

sampler. (Platinum only).

5. Activate the program to R

and the table

will turn to locate #Bottle 1. After the table
has stopped make sure the discharge tube is
centered on the bottle. If the discharge tube
is not centered, rotate/adjust the discharge
tube to the center of the bottle.

Note

Bottle caps can be stored in the center of the bottle
rack.

Figure 2-1 Bottle rack with 24-1 liter bottles

Содержание Optima

















































































































Результаты поиска

Содержание Optima

Отзывы:

Teledyne Optima, Карманный справочник, Страница: 27 / 112

Результаты поиска

Содержание Optima

Отзывы: