Teledyne Optima Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 112

Teledyne Optima Скачать руководство пользователя страница 20

Platinum/Optima CVE Refrigerated Sampler

2-2

2.2 Positioning the Sampler

There are a few considerations when selecting a

site for the sampler. The foremost concern
should be personal safety.

The installation and use of this product may

subject you to dangerous working conditions
that can cause you serious or fatal injuries.

Take any necessary precautions before entering

the work site. Install and operate this product
in accordance with all applicable safety and
health regulations, and local ordinances.

WARNING

If this product is used in a manner not specified
in this manual, the protection provided by the
equipment may be impaired.

WARNING

This product has not been approved for use in
hazardous locations as defined by the National
Electrical Code.

WARNING

The sampler is heavy. When lifting, use a
two-person lift from the right and left sides. When
possible, move the sampler using a two-wheeled
hand cart from the side. To prevent damage to the
refrigeration system, do not tip the sampler more
than 45°.

«
...
18
19
20
21
22
...
»

Содержание Optima

















































































































Отзывы:

Нет отзывов