Teledyne MagnaStar C-2000 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 100

background image

F4. Link selection dialing prefixes for individual calls

#61#

Selects Air-Ground (disables Auto Link Switch)

#62#

Selects GroundCell (disables Auto Link Switch)

#63#

Selects SATCOM (disables Auto Link Switch)

#612#

Selects Air-Ground then GroundCell (SATCOM not included
in the rotation). Used with Genesys Airshow.

NOTE 1: These prefixes override the station default link (see Section VI, D1).

NOTE 2: Both Baud Rate and Link Selection prefixes can be utilized for the same

call (order sequence does not matter)

NOTE 3: The Link Selection prefixes can be used for all call types (i.e. Voice, Fax,

Modem and TDD).

G. Telecommunication Device for

the Deaf (TDD)

Place the handset off-hook. If your TDD has a RJ-11 cord, connect the
cord into the RJ-11 jack on the handset. Press “5” (TDD) and dial the
telephone number from either the handset or the TDD unit.

NOTE 1: For a ground-to-air TDD call, a delay greater than 20 seconds is needed

after the dialed number. This is necessary to bypass the voice prompts,
otherwise the ground modem will disconnect the call.

NOTE 2: It is not necessary to press “5” (TDD) if this handset has been config-

ured as a TDD station. To set the station mode refer to Section VI, B5.

If you want the TDD unit to be acoustically coupled, make certain that
no RJ-11 cord is connected prior to dialing the telephone number from
the handset. When prompted, press “+” (To Use TDD Acoustic
Coupler) to indicate your desire to use the TDD acoustic coupler.

Press “End Call” to terminate the call. The connection will be termi-
nated automatically if the ground party hangs up first.

27

(Rev. 8/04)

®

«
...
34
35
36
37
38
...
»

Содержание MagnaStar C-2000





































































































Отзывы:

Нет отзывов

Похожие инструкции для MagnaStar C-2000

Бренд: Yealink Страницы: 15

Бренд: Yealink Страницы: 12

Бренд: Yealink Страницы: 3

Бренд: TRIGA Страницы: 33

Бренд: GE Страницы: 84

Бренд: BT Страницы: 70

Бренд: Karel Страницы: 80

myPhone Jazz 202112

Бренд: mPTech Страницы: 65

Бренд: HTC Страницы: 232

Бренд: Wheelock Страницы: 6

Бренд: Moshi Страницы: 7

Бренд: Uniden Страницы: 1

Бренд: Tecdesk Страницы: 18

Бренд: LG Страницы: 84

Бренд: Brother Страницы: 10

Бренд: Cisco Страницы: 202

KXTGA930 - DIGITAL CORDLESS HANDSET INSTALL

Бренд: Panasonic Страницы: 5

Бренд: Icom Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды