Teledyne HDO9000 Скачать руководство пользователя страница 85

Страница: 85 / 188

Display

Q-Scape Mosaic

, a single set of four tabs arranged so that all are viewed simultaneously. Note

that the decoder table appears only in Tab1, since it is part of the display associated with the

trace in that tab. However, in the Q-Single example above, the table appears along the entire

bottom of the window, because Tab1 takes up the entire display area, whereas here Tab1

takes up only the upper left quadrant.

In Q-Scape modes, channel, math, memory, and zoom descriptors appear in the tab where the trace is

open, while Timebase and Trigger descriptors remain outside the tabs, since they are not associated

with any one trace.

Note:

If you switch from Normal mode into any Q-Scape mode, all traces will move to Tab 1,

from which you can drag-and-drop to redistribute them to other grids. In Q-Scape Single mode,

you will not be able to drag-and-drop traces across tabs, only to other Tab1 grids.

To rename Q-Scape tabs after they open:

1. Touch-and-hold (right-click) on the

Tab <#>

until Rename pops up.

2. Touch

Rename

3. Enter the

New Alias

, then touch

Extended Display

If an external monitor is installed, you can extend the display to take advantage of the greater screen

area.

1. On the Display dialog, select

Extend Grids Onto 2nd Monitor

. The Select Grid pop-up opens.

Note:

Extend Grids... only appears when a second monitor is connected. Configure

Windows so that the instrument is the primary display and is extended, not duplicated.

2. Switch to the Extended Display submenu and choose a

Grid

style. Tab 1 and the external

monitor will share the same grid style.

3. Drag-and-drop descriptor boxes to place traces on the desired grids.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды