Teledyne HDO9000 Скачать руководство пользователя страница 23

Страница: 23 / 188

Oscilloscope Set Up

Connecting to Other Devices/Systems

Make all desired cable connections. After start up, configure the connections using the menu options

listed below. More detailed instructions are provided later in this manual.

LAN

The instrument accepts DHCP network addressing. Connect a cable from the Ethernet port on the

side panel to a network access device.

To assign a static IP address, go to Utilities > Utilities Setup > Remote and choose Net Connections

from the Remote dialog. Use the standard Windows networking dialogs to configure the device

address.

Go to Utilities > Preference Setup > Email to

configure email settings

USB Peripherals

Connect the device to a USB port on the front or side of the instrument.

Printer

The HDO9000 supports USB printers compatible with the instrument's Windows OS. Go to Utilities >

Utilities Setup > Hardcopy to

configure printer settings

External Monitor

You may operate the instrument using the built-in touch screen or attach an external monitor for

extended desktop operation. A properly configured external touch-screen monitor will take on all the

touch-screen capabilities of the internal display.

Note:

The oscilloscope display utilizes Fujitsu touch-screen drivers. Because of conflicts,

external monitors with Fujitsu drivers can not be used to control the system, only as displays.

The HDO9000 supports WQXGA monitors with 2560x1600 resolution.

Connect the monitor cable to the DisplayPort connector on the side of the instrument (you can use an

adaptor if the monitor cable has a different interface). Monitors with DVI-D interfaces are also

supported. Minimize the X-Stream application and use the Windows controls to configure the display.

Configure the instrument as the primary monitor and be sure to extend, not duplicate, the display.

Remote Control

Go to Utilities > Preference Setup > Remote to

configure remote control

. Connect the devices using

the cable type required by your selection. TCP/IP over Ethernet is generally supported, as is USB over

the USBTMC connection. GPIB is also supported with the correct hardware option installed.

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды