manualshive.com logo in svg

Teledyne HDO9000, Руководство оператора

Поделиться
Скачать
Teledyne HDO9000 Скачать руководство пользователя страница 173

Utilities

Miscellaneous

These other Preference settings are located on the

Miscellaneous

dialog.

To add the Teledyne LeCroy logo to print output, check

Print Teledyne LeCroy Logo When Printing Grid

Area Only

. This identifies the instrument as the source of the image.

You can adjust zoom behavior as follows:

l

Dimming

darkens/shades those areas of the source waveform that are not part of the Zoom

trace.

l

Control Sensitivity

adjusts the sensitivity of the front panel knobs.

Optimized

applies an

acceleration algorithm to the knobs.

Legacy

detects rotation of the front panel knobs in a

manner similar to our legacy oscilloscopes.

Serial Decode Annotation Position:

If you have Serial Trigger or Decode options installed on your

instrument, this control determines the placement of annotation labels relative to the trace line. It

does not appear if there are no installed options.

l

On Trace

places the label close to the line.

l

On Noisy Trace

sets the label further from the line to accommodate potential noise spikes in

the trace.

Check

Enable HTTP Screen Capture

to enable remote capture of the touch screen display over a

netowrk. This setting is required to use the instrument with the WaveStudio software.

163

Содержание HDO9000





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды