Teledyne HDO9000 Скачать руководство пользователя страница 117

Страница: 117 / 188

Math and Measure

Math

Math traces (F

) display the result of applying a mathematical operation to a source trace. The

output of a math function is always another trace, whereas the output of a measurement parameter is

a tabular readout of the measurement.

Math can be applied to any channel (C

), zoom (Z

), or memory (M

) trace. It can even be applied to

another math trace, allowing you to chain operations (for example, trace F1 can show the average of

C1, while trace F2 provides the integral of F1). Functions such as Trend can be applied to

measurement parameters (P

) to plot the history of the measurement.

In addition to the extensive math capabilities that are standard with every instrument, enhanced math

analysis tools customized for various industries and applications are offered through optional

software packages. To learn about math tools available in each optional package, see the product

datasheets at

teledynelecroy.com

If you have installed software options, the new capabilities are usually accessed through the Analysis

menu, rather than the Math menu, although special measure parameters and math functions will be

available when using Measure and Math dialogs.

107

Содержание HDO9000





























































































































































































Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды

Teledyne HDO9000, Руководство оператора

Результаты поиска

Содержание HDO9000

Отзывы:

Бренды по названию

Популярные бренды