background image

FIRE

R M LD

FIRE

R M LD

Operator’s Manual

9

GAS LASER

Doc No. 16162 Rev A, GAS LASER Operator Manual 

© 2021 Teledyne Gas Measurement Instruments Ltd. All rights reserved.

Specifications

General 

Gas Laser Weight

3 lbs (approx.)

Carry Case Dimensions

21” x 17.5” x 9.5”

Display

3.5” color LCD

Storage

Internal SD card (not removable)

Power 

Battery

Removable 

Rechargeable  

Lithium-ion pack, 10.8 VDC 3.2Ah

Battery Run Time

8 hours at 32° F (approx.)

Battery Charger

External 

110-240 VAC, 50/60 Hz Universal

Charge Time

2-3 hours full charge (approx.)

Charging Indicator

Integrated into Dual Battery Charger

Detection/Measurement System 

Detection Method

Tunable Diode Laser Absorption 

Spectroscopy (TDLAS)

Detection Distance

100 ft (30m) nominal - may vary 

due to background type and  

conditions

Measurement Range

0 to 50K PPM-M

Sensitivity

5 PPM-M at distances from 0 to 

100 ft (30m)

Beam Size

Conical in shape with a 22”  

diameter at 100 ft (55cm at 30m)

Display 

Resolution

320x240

Camera 

Color

Aperture

f/2.6

FOV

94DEG (at 6.0mm image circle)

Lasers 

IR Laser

Class I

Spotter Laser

On time duration is 2 minutes 

Class 2 (II) <2mW @ 532nm 

Spot size is 7mm at 15M

Complies with 21 CFR 1040.10

and 1040.11 except for deviations

pursuant to Laser Notice No. 50,

dated June 24, 2007

Eye Safety Warning

Do not stare into beam or  

view directly with optical  

instrument 

Avertissement de sécurité des yeux 

Ne jamais fixer le faisceau ni le 

regarder directement avec des 

instruments optiques.

GPS                                                 

Compatible With

GPS 

GLONASS 

Beidou 

Galilieo

Communication 

Bluetooth 4.2 BLE  

(to support future features and 

mobile applications)
WiFi

USB Dual Mode

USB Port Max Rating:

UM = 5V, IN = A

Alarms 

Digital Methane Detection (DMD)

Audible tone and visible color 

border when detection threshold 

exceeded 

Adjustable Detection Alarm Level 

50’ 

1 to 200 PPM M

100’ 

1 to 400 PPM M

System Fault & Warnings

Audible alarm and visual  

indication on the display

Testing 

Built-In Self Test

Verifies operation and adjusts 

laser wavelength for maximum 

sensitivity

Test Gas Cell 

Integrated within carrying case

Data Logging 

Saves to Internal Memory

FAULT logs 

Self Test logs 

Captures

Data Collected

Includes, but not limited to: 

CH4 PPM-M measurement 

GPS location 

Timestamp 

Battery level 

Battery voltage 

Serial number of the instrument

Operating Conditions 

Operating Temperature

0° to +122° F (-17° to 50° C)

Humidity

5 to 95% RH, non-condensing

Altitude

Up to 6560 ft (2000 m)

Environment of Use

Pollution degree 2 or better

Outdoor use

Regulatory 

Instrument Protection 

IP54 (water splash and dust  

resistant)

Compliance

EMC (EN61000-6-2, EN6100-6-4)

Low Voltage Directive 

(2014/35/EU)

Radio Equipment Directive

(2014/53/EU) 

ETSI EN 301 489-1 v2.2.0
EN 61326-1:2013

 

47 CFR Part 15 & ICES-003

Ordinary Location Safety 

UL 61010-1

CAN/CSA-C22.2 No 61010-1-12

Hazardous Location Safety 

Class I, Zone 2, AEx ic op is IIA T4 Gc
Class I, Division 2, Group D 

Intrinsically Safe

Содержание GAS LASER
































Отзывы: