Teledyne ADQ8-4X Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 46

Teledyne ADQ8-4X Скачать руководство пользователя страница 17

19-2302 A
2020-09-16

17(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

17(46)

illustrates how the triggers are accepted or rejected in the window mode.

#

DESCRIPTION

USER COMMAND

REF

a

External trigger input signal on front panel connector.

b

External sync input signal on front panel connector.

c

Other available sources (see

SetTriggerMode

for a list).

d

Select source for blocking triggers.

SetupTriggerBlocking

e

Before activating the trigger blocking any selected trigger may pass.

SetupTriggerBlocking

f

This signal is ignored as the trigger blocker is not armed

g

Select trigger source

SetTriggerMode

h

Start receiving triggers. Note that triggers are still blocked.

ArmTrigger

i

The unblocking of triggers is armed and can be activated by (d).

ArmTriggerBlocking

j

Triggers are blocked until the first accepted blocker signal.

SetupTriggerBlocking

k

The trigger blocker can also be set up with a window function where
triggers are accepted or rejected during a user-defined window.

SetupTriggerBlocking

l

The trigger blocker can also be set up as a gate where triggers are
accepted during a gated time set by signal (d).

SetupTriggerBlocking

Figure 8: Blocking and gating of triggers.

()

*

+,

()$ $

*

,

- $

()

*

,

.

/0 12.

"3

/0 4

5

*

,

*

,

6

3

*

,

7

"3

*

,

*

,

*

,

*

,

*

,

*

,

*

,

«
...
15
16
17
18
19
...
»

Содержание ADQ8-4X















































Отзывы:

Нет отзывов