Teledyne ADFM Hot Tap Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 116

Teledyne ADFM Hot Tap Скачать руководство пользователя страница 78

ADFM® Flow Meter



Section 2 Setup and Installation

2-58

2.12 Data Retrieval

This section offers a brief overview of collecting data from your
ADFM system with Teledyne Isco’s software programs. For full
details of site setup and data management, refer to the software
instruction manual.

Note

The flow meter’s recorder must be cleared following data
retrieval. Save all downloaded data and, prior to redeployment,
erase the recorder and restart the ADFM. This applies to both
Flowlink and WinADFM software programs.

2.13 Flowlink

To begin downloading data from the ADFM through direct con-
nection:

1. Connect the computer to the ADFM flow meter with the

communication interface cable.

2. Start Flowlink software.

3. In the workspace on the left, open the desired site file. The

site window opens.

Figure 2-62 Site Info tab: Connect and Retrieve Data buttons

4. On the Site Info tab, click the Connect button.

5. Once the site is online, the Retrieve Data button becomes

active. Click the Retrieve Data button to download data
from the site.



A progress bar will indicate the download status.

«
...
76
77
78
79
80
...
»

Содержание ADFM Hot Tap





















































































































Отзывы:

Нет отзывов