Teledyne ADFM Hot Tap Скачать руководство пользователя страница 77

Страница: 77 / 116

ADFM® Flow Meter

Section 2 Setup and Installation

2-57

Table 2-2 BIT Hexadecimal Code Definitions

Code

Definition

Explanation

01nnnnnn

Autostart:

Unit has been restarted or restarted itself.

80nnnnnn

Modem dial failure

40nnnnnn

Modem listen failure

20nnnnnn

Recorder failure

10nnnnnn

Recorder full

08nnnnnn

Transducer communication failure

04nnnnnn

Power time fail:

Motherboard failure

02nnnnnn

Fifo fail:

008nnnnn

DeMod LCA fail:

00000040

Intrup Err:

00000020

00000010

00000008

Divo Err:

00000004

Inst Err:

00000002

Addr Err:

00000001

Bus Err:

Possible motherboard failure, but may
correct itself upon restart.

004nnnnn

Comm Timeout: Communication times out in the ADFM after several minutes of no activity.



To reestablish communication, disconnect the ADFM from the computer and then reconnect.

002nnnnn

Pressure fail: Failure of secondary depth sensor if it is a pressure type sensor;



no code for other sensor types.

00000080

Cold WU (wakeup): Manual restart occurred while ADFM was connected to computer.

Note

Each code indicates one error or event type. However, if two or more events are present, the code
will appear as the sum of the most significant digits of their corresponding codes.



Example: If the ADFM has been restarted and also experienced a transducer communication failure,
the code displayed would be:

09nnnnnn

Содержание ADFM Hot Tap





















































































































Результаты поиска

Содержание ADFM Hot Tap

Отзывы:

Teledyne ADFM Hot Tap, Инструкция по установке и эксплуатации, Страница: 77 / 116

Результаты поиска

Содержание ADFM Hot Tap

Отзывы: